Prime Hold 33 Review: Real Speeds, Draw Cycle & Tuning
Prime Hold 33 Review: Real Speeds, Draw Cycle & Tuning

Prime Hold 33 Review: Real Speeds, Draw Cycle & Tuning

Prime's Hold lineup replaces the Divide series, and after spending some time shooting the Hold 33, I think Prime made some meaningful improvements.

The riser still has that recognizable Prime center-grip design, but there's a new CNTRAX Cam System, a completely different approach to tuning with ALIGN, an updated Nano2 Grip, and a built-in back-bar mounting system.

I've said before that the more I shoot Prime bows, the more I enjoy them. The Hold 33 continues that trend. We put it on the draw board, measured the actual draw weight and holding weight, tested multiple arrow weights through the chronograph, and spent time shooting it to see how all these changes actually feel.

Here's what we found.

Quick Answer: Is the Prime Hold 33 Worth It?

The Prime Hold 33 is a premium hunting bow that combines strong real-world speed, an exceptionally quiet shot, and extensive tuning and draw-cycle adjustability.

In our testing of the 33/6, we averaged 306.7 fps with a 400-grain arrow at a nominal 30-inch draw length and 290.5 fps with the same arrow at 28 inches. Prime advertises 334 fps IBO, and our IBO-arrow test averaged 331.2 fps.

What impressed me most wasn't just the speed. It was the grip, the lack of vibration, the adjustable CNTRAX Cam, and how much tuning adjustment you get from ALIGN without putting the bow in a press for those adjustments.

Watch: Prime Hold 33 Full Review and Speed Test

In this video, I break down the Hold 33, demonstrate the new features, measure the bow on the draw board, make adjustments to the cam, and run our chronograph testing.

The Prime Hold Lineup

The Hold replaces Prime's Divide series and is available in four axle-to-axle lengths: 31, 33, 35, and 37 inches. Each length is offered with either a 6-inch or 7-inch brace height.

For this review, we're looking at the Hold 33/6. Personally, I think the 33-inch platform is going to be one of the heavy hitters in the lineup.

If somebody comes into the shop looking for one bow to hunt with, practice with, and potentially shoot some 3D, 33 inches is a length I really like. It gives you a little more bow than a compact hunting setup without getting excessively long.

That doesn't mean a 33-inch bow is automatically the right choice for everyone. Your draw length, how you hunt, and how the bow aims for you all matter.

Prime Hold 33 compound bow tested at Extreme Outfitters

Prime Hold 33 Specifications

Here are the published specifications for the Hold 33/6, followed by the numbers we measured on our test bow.

Manufacturer Specifications: Hold 33/6

Axle-to-Axle: 33 inches

Brace Height: 6 inches

IBO Speed: 334 fps

Mass Weight: 4.2 lb

Draw Length Range: 26–31 inches

Available Draw Weights: 40–80 lb options, including 75 lb

Cam System: CNTRAX

Tuning System: ALIGN Limb-Pocket Tuning

Grip: Nano2 Grip

Extreme Outfitters Test Bow Measurements

Measured Axle-to-Axle: 33 inches

Measured Brace Height: 6 inches

Weight With Arrow Rest: 4.6 lb

30-Inch Mod Setup: 70.8 lb peak draw weight

Let-Off: 86.4%

Holding Weight: 9.6 lb

One thing worth mentioning: the number three mod, nominally set for 30 inches, measured approximately 30.5 inches on our draw board. That's the measurement of our test setup, not a claim that every Hold will measure the same way.

Actual draw length and holding weight are worth checking when you set up your bow, especially when comparing real-world speeds.

What's New on the Prime Hold 33?

Prime didn't just update the appearance of the Divide and call it something different. There are several changes that affect tuning, the draw cycle, grip feel, and how you can set the bow up.

ALIGN Limb-Pocket Tuning System

This is probably one of my favorite things about the new Hold.

Prime's ALIGN system allows you to move the limb and limb pocket laterally together to adjust the bow's alignment. Instead of relying exclusively on shimming the cams, you now have another way to make precise tuning adjustments.

The system is designed to be adjusted with Allen keys without requiring a bow press for the supported ALIGN adjustments.

Close-up of Prime Hold ALIGN limb-pocket tuning system

In our testing, the system offered a considerable amount of adjustment. We were able to influence paper-tear results by an inch or more through the available adjustment range.

That doesn't mean you should immediately start moving the limb pocket every time you see a paper tear. You still need to establish your initial setup, confirm your arrow is appropriate for the bow, and account for shooting form.

But if you're somebody who likes to work on your own equipment, I think you're going to appreciate how accessible this system is.

There's still the ability to shim the cams, but I expect a lot of people will use ALIGN for much of their lateral tuning.

Our Take: ALIGN provides a practical way to make small alignment corrections. It's a useful tuning feature, but it doesn't replace proper bow setup, arrow selection, or following Prime's adjustment procedures.

CNTRAX Cam System and Adjustable Draw Stop

The CNTRAX Cam replaces the CORE Cam on Prime's flagship Hold lineup.

I thought the CORE Cam was phenomenal, so I was interested to see how Prime would improve on it.

Like the previous system, CNTRAX uses draw-length-specific modules. You still have half-inch draw-length options, and the idea is to optimize cam performance across the available draw lengths instead of relying on one broad rotating adjustment range.

The biggest improvement for me is the adjustable draw stop and back-wall characteristics.

By changing the draw-stop setting, you can change how the bow transitions into the valley and how it feels once you're holding at full draw.

That's important because not everybody likes the same draw cycle. Some people want a longer, more forgiving valley. Others want a tighter holding position that doesn't allow as much movement before the cams start rolling forward.

Prime also describes improved string-angle characteristics with the CNTRAX Cam System.

We actually made a draw-stop adjustment during our review, and the difference was noticeable. I'll get into that when we talk about how the bow shoots.

Redesigned Nano2 Grip

Prime already made one of my favorite grips, and I think the updated Nano2 Grip is another improvement.

The new version is screwless, has a flatter back and throat area, and maintains a relatively low-profile shape.

It also has a triangle on the back identifying the center of the bow.

That might sound like a small detail, but I really like it. It's a clear reference point when you're trying to establish repeatable hand placement.

The grip also has an insulated, tacky feel rather than feeling like you're holding directly against a cold metal riser.

For me personally, the grip is one of the strongest parts of this bow.

Updated Center-Grip Riser and Hybrid Construction

The Hold retains Prime's center-grip design, but the riser geometry has changed. Prime moved toward a straighter, less-reflexed riser design with shorter limbs.

The bow also incorporates Prime's Advanced Structures Technology, using carbon reinforcement and aluminum construction in the riser.

Prime makes specific claims about stiffness and weight reduction with this technology. Those are manufacturer engineering claims rather than measurements we independently verified during this review.

What we did measure was the actual bow weight. Prime lists 4.2 pounds bare, and our test bow weighed 4.6 pounds with the arrow rest installed.

Weight matters, but you've also got to look at balance. A bow that weighs less on paper doesn't automatically aim better for every shooter.

SIM Integrated Back-Bar Mount

Another feature I really like is the new SIM, which stands for Simple Integrated Mount.

Essentially, Prime built a rear stabilizer mounting location directly into the bow.

That means you can run a compatible back-bar setup without necessarily adding a separate offset mounting bracket.

Prime Hold 33 SIM integrated rear stabilizer mounting system

For somebody who likes a front bar and back bar, that's a nice option. It can simplify the setup and eliminate the weight of an additional mounting bracket.

The Hold also supports compatible integrated accessories, including Picatinny-style sight mounting, integrated rest options, Prime's TriLite stand, and compatible SherpaLite quivers.

Before purchasing accessories, make sure the exact mount and accessory are compatible with your specific bow configuration.

How Does the Prime Hold 33 Actually Shoot?

Specifications are one thing. How the bow feels when you draw it, settle into the valley, aim, and execute the shot is another.

We tested the Hold 33 at two draw-length settings to get a better picture of the cam system.

30-Inch Draw-Length Setup

I started with the number three mod, nominally a 30-inch setting. On the draw board, our bow measured closer to 30.5 inches, which is a little long for me.

At this configuration, we measured:

Peak Draw Weight: 70.8 lb

Let-Off: 86.4%

Holding Weight: 9.6 lb

The draw cycle builds throughout the draw, and there is some stacking toward the back before the cam rolls over.

At this particular setting, the valley was very forgiving. It felt like I would really have to push the bow forward before it wanted to roll over.

The back wall was rock solid.

What surprised me was how quiet the bow was. There was no noticeable twang, very little post-shot feedback, and essentially no vibration that stood out while shooting.

I've shot bows that feel good during the draw but have noticeable vibration after the shot. This wasn't one of them.

28-Inch Draw-Length Setup

We then switched to the number seven mod for the nominal 28-inch setup.

Peak Draw Weight: 71.4 lb

Let-Off: Approximately 84%

Holding Weight: 11.4 lb

At 28 inches, the draw still builds before rolling over, and you can feel a little dump near the back of the cycle.

That's where the adjustable draw stop becomes interesting.

What Happened When We Adjusted the Draw Stop?

I made a small adjustment during the video, and it changed the way the bow felt.

The valley became a little shorter and less forgiving, but the draw cycle felt smoother coming into the back wall. There wasn't as much of that noticeable dump into the valley.

For somebody who likes a tighter holding position, that could be a good trade-off.

For somebody who prefers a longer valley, the original setting may feel better.

That's the advantage of this system. You have some ability to tailor the back half of the draw cycle to how you actually like to shoot.

Changes to the stop can also influence holding characteristics, so check the finished setup rather than assuming the original measurements remain the same.

Prime Hold 33 Real-World Speed Test

Now let's get into the numbers.

We ran the bow through the chronograph using several different arrow weights at nominal 30-inch and 28-inch draw-length settings, with the bow in its approximately 70-pound configuration.

All the speeds below are three-shot averages from our Extreme Outfitters test.

Extreme Outfitters Prime Hold 33 compound bow chronograph speed testing

30-Inch Draw-Length Speed Results

IBO Test Arrow

331.2 FPS

400-Grain Arrow

306.7 FPS

450-Grain Arrow

295.8 FPS

540-Grain Arrow

271.3 FPS

28-Inch Draw-Length Speed Results

400-Grain Arrow

290.5 FPS

450-Grain Arrow

277.6 FPS

Speed Test Takeaway

Prime advertises 334 fps IBO for the Hold 33/6. Our IBO-arrow test averaged 331.2 fps, which is close to the published rating. Actual arrow speed depends on the complete setup, including measured draw length, draw weight, arrow weight, and cam settings.

During the IBO test, we had one chronograph reading that was clearly outside the expected range. We took an additional shot rather than including that questionable reading in the average.

Looking at the actual hunting-arrow numbers, I'm impressed.

A 400-grain arrow averaging 290.5 fps at the 28-inch setting is a strong result for this setup. And even with a 450-grain arrow, we were averaging 277.6 fps.

That doesn't mean everybody needs to run a 400-grain or 450-grain hunting arrow. Arrow spine, length, point weight, broadhead choice, and tune still need to be considered together.

The important thing is that the Hold gives you a useful amount of performance across different arrow weights.

Interested in the Prime Hold 33?

Explore the Hold 33 specifications and configuration options at Extreme Outfitters. Our archery team can help you compare draw lengths, choose accessories, and get the bow properly set up.

VIEW PRIME HOLD 33

Changing Draw-Length Modules on the Hold 33

Prime makes it pretty straightforward to identify the correct draw-length modules.

There's a reference on the right lower limb identifying the module setup for the different draw lengths.

The modules are labeled A and B. On a right-handed bow, A goes on the top cam and B goes on the bottom. On a left-handed bow, that arrangement is reversed.

The modules are retained with two screws, and the change is relatively straightforward when you follow Prime's instructions.

The thing to remember is that the Hold uses specific modules for the desired draw length. It isn't simply a rotating module system where you turn one module through the entire draw-length range.

Make sure you're using the correct module pair and verify actual draw length and draw-stop settings after making changes.

Which Prime Hold 33 Should You Choose?

The Hold 33 is available in both 6-inch and 7-inch brace-height configurations. They're built around the same flagship platform, but there are differences worth considering.

Prime Hold 33/6

Brace Height: 6 inches

IBO: 334 fps

Draw Length: 26–31 inches

Best Fit: Shooters who prefer the shorter brace-height configuration and want the higher advertised speed potential.

Prime Hold 33/7

Brace Height: 7 inches

IBO: 326 fps

Draw Length: 27–32 inches

Best Fit: Shooters who prefer a longer brace height or need a draw length beyond the 33/6 range.

The 6-inch model gives you the higher published IBO number, but speed isn't everything.

A 7-inch brace height can be attractive to shooters who prefer that geometry or want a little more clearance through the shot. That doesn't automatically mean the 7-inch version will shoot better for everyone.

My recommendation is to shoot both if possible. The way the bow fits and aims for you matters more than choosing one based strictly on the IBO number.

Prime Hold 33 vs. Prime Divide 33: What Changed?

Since the Hold replaces the Divide, this is a natural comparison.

I liked the Divide series, and a lot of the things that made those bows appealing carry over. You still have Prime's center-grip approach, integrated accessory options, and draw-length-specific modules.

But the Hold makes meaningful changes in several areas.

Major Changes on the Hold

  • New CNTRAX Cam System replacing the CORE Cam
  • Adjustable back-wall and draw-stop characteristics
  • New ALIGN limb-pocket tuning system
  • Redesigned, less-reflexed riser geometry
  • Updated screwless Nano2 Grip
  • SIM integrated rear stabilizer mount

For me, the two biggest changes are the cam and the tuning system.

The CORE Cam was already a strong performer, but the CNTRAX adds another level of customization to how the bow feels at full draw.

ALIGN also changes how you can approach lateral tuning adjustments.

Does that mean you need to replace your Divide if you're already happy with it? Not necessarily.

But if you're shopping for a new Prime, those features give you a reason to spend time with the Hold.

For a closer look at the previous platform, read our Prime Divide 33 Review.

Who Is the Prime Hold 33 Best For?

I think the Hold 33 makes sense for somebody who wants a premium hunting bow but also cares about how it shoots outside of hunting season.

The 33-inch platform is a good middle ground for a lot of shooters. It isn't a compact 29- or 30-inch hunting bow, but it also isn't a long target-style setup.

I'd especially consider the Hold 33 if you value:

  • A quiet bow with minimal post-shot vibration
  • A solid back wall with adjustable holding characteristics
  • Accessible, precise tuning adjustments
  • A comfortable, repeatable grip
  • Integrated accessory mounting options
  • Strong performance with practical hunting-arrow weights

The biggest consideration is fit.

If somebody comes into the shop and tells me they want the fastest bow available, I'm still going to have them draw it and shoot it. You don't buy a bow based on a chronograph number alone.

The Hold's draw cycle does build toward the back, and depending on how the draw stop is configured, you'll notice the rollover into the valley.

Some people are going to love that. Others may prefer a different draw-cycle profile.

That's why I always recommend evaluating a bow at your actual draw length and preferred draw weight.

What to Consider Before Buying the Hold 33

Don't Compare Speed Without Comparing Setups

We measured 331.2 fps with an IBO test arrow, but that doesn't mean a finished hunting arrow will produce the same speed.

Draw length, draw weight, actual arrow weight, and the complete bow configuration all matter. Compare the conditions behind the numbers, not just the advertised IBO ratings.

Don't Ignore the Draw-Stop Adjustment

The adjustable stop is one of the biggest features of the CNTRAX Cam.

If the bow feels like it has too much valley or rolls over more abruptly than you prefer, the stop configuration may be worth evaluating before deciding you don't like the cam.

Don't Tune Around a Poor Initial Setup

ALIGN gives you plenty of adjustment, but you've still got to establish a proper starting point.

Check the bow's configuration, arrow compatibility, rest position, and shooting form before using limb-pocket adjustments to chase a paper tear.

Make adjustments using Prime's recommended procedures, and verify the results through actual shooting.

Prime Hold 33 Frequently Asked Questions

How fast is the Prime Hold 33?

Prime rates the Hold 33/6 at 334 fps IBO. In our Extreme Outfitters test, the IBO-arrow average was 331.2 fps. With a 400-grain arrow, we averaged 306.7 fps at the nominal 30-inch setting and 290.5 fps at 28 inches.

How much does the Prime Hold 33 weigh?

Prime lists the Hold 33/6 at 4.2 pounds bare. Our test bow weighed 4.6 pounds with the arrow rest installed.

Does the Prime Hold 33 require a bow press for tuning?

The ALIGN system allows supported lateral limb-pocket adjustments without a bow press. Other procedures, including certain cam or string-related work, can still require specialized equipment.

What cam does the Prime Hold use?

The Hold uses Prime's CNTRAX Cam System, which replaces the CORE Cam on the flagship platform. It features draw-length-specific modules and adjustable back-wall characteristics.

Is the Prime Hold 33 good for hunting?

Yes, the 33-inch axle-to-axle length makes it a practical option to evaluate for treestand, saddle, blind, and Western hunting setups. The right choice still depends on your draw length, preferred bow length, and overall setup.

Should I choose the 6-inch or 7-inch brace height?

The 33/6 offers a higher published IBO speed and a 26–31-inch draw-length range. The 33/7 offers a longer brace height and a 27–32-inch draw-length range. Try both configurations if possible and choose based on fit and shooting preference.

Bottom Line: Our Prime Hold 33 Review

I've really enjoyed shooting the Prime bows over the last few years, and the Hold 33 is another one that impressed me.

The grip is fantastic. The bow is extremely quiet in our testing, with almost no noticeable vibration after the shot. And the real-world speed numbers are right where I'd want to see them from a premium hunting bow.

But the biggest improvements are the CNTRAX Cam and ALIGN Tuning System.

Being able to adjust the way the bow holds at full draw is a feature I really appreciate. The same goes for having a practical, pressless method of making supported alignment adjustments.

Add the updated riser, SIM back-bar mount, and integrated accessory options, and Prime has put together a strong flagship package.

Would I recommend shooting the Hold 33? Absolutely.

If you've been putting off trying a Prime, I'd encourage you to get one in your hands. You might be surprised by how much you like the way it draws, aims, and shoots.

Explore Prime Archery at Extreme Outfitters

Shop our selection of Prime bows and accessories, or contact our archery team for help choosing the right setup.

VIEW PRIME HOLD 33 EXPLORE PRIME ARCHERY

Visit our full-service archery shop in Jacksonville, North Carolina, for fitting, setup, and tuning assistance.

Related Articles

Prime Divide 33 Review

See our real-world testing of the previous Prime platform and how it compares with the Hold.

Darton TriTech 35 vs. Prime Divide 35

Our Bow Wars comparison puts two longer hunting bows through setup, tuning, speed, and shooting tests.

Prime SherpaLite Quiver Review

A closer look at Prime's integrated quiver system and what to consider when building your bow.


Please note, comments must be approved before they are published

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.