Black Eagle Deep Impact Front Of Center Outsert System - Stainless Steel - Extreme Outfitters
Black Eagle Deep Impact Front Of Center Outsert System - Stainless Steel - Extreme Outfitters

Black Eagle Deep Impact Front Of Center Outsert System - Stainless Steel

33555|350

Regular price$48.99
/

  • Low stock - 7 items left
  • Backordered, shipping soon

We ship via USPS and UPS. Some shipping methods may not be available in all areas. All PO boxes must be shipped via USPS.

FLAT RATE SHIPPING

Flat rate shipping is a flat rate of $8 available for most orders shipping to the continental US only. Some oversize items are not available for flat rate shipping.

FREE SHIPPING DISCOUNTS

Free shipping options and discounts are only valid in the continental US. Not Valid on oversized items. (Tree stands, Crossbows, Bows, Targets)

HOLIDAY SHIPPING

We are closed New Year’s Day, Easter, 4th of July, Thanksgiving, and Christmas, and are unable to ship on these days. Additionally, please observe the holiday schedule for USPS and UPS during these times.

INTERNATIONAL SHIPPING

We are only able to accept credit cards from the United States. We do ship internationally but the only form of payment we can accept from other countries is PayPal.

SHIPPING TIMES

Our web department is open Monday-Friday, and shipments can only be made on those days. Most orders will be processed and shipped the same or next day, depending on product availability. If there is a stock issue with your order, you will be notified by phone or email as to the status. In some cases, it may be more efficient to have your order drop shipped from the manufacturer, if so, tracking info may not be readily available.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

Front Of Center Outsert System (Patent#US10203185)
QTY IS 1 DOZEN:
Our New Front Of Center Outsert System is designed for those that want more weight upfront and ease of use of Outserts. The F.O.C.O.S is made of 3 parts. One is the black anodized 7075 T6 aluminum alloy outsert or Stainless Steel Option. Two is a Stainless steel Retention post In The Aluminum Outserts Model and Aluminum in the Stainless Steel Outsert Model that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Deep Impact, Instinct or X-Impact shafts then the F.O.C.O.S are sure to be a hit!

Insertion Depth of Arrow in Outsert is .610 almost 5/8"
Outsert adds Approximately 1.090" to end of the Arrow



The Deep Impact & X-Impact Outsert Weights are a Follows:

ALUMINUM OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 80 Grains

STAINLESS STEEL OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 100 Grains

    • To install the F.O.C.O.S System
    1. Select the right outsert for the right shaft.
    2. Glue in Stainless steel retention Post
    3. Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
    4. If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on shaft. Start slowly so you don't remove to much off the arrow.
    5. You should have approximately 3/4 of an inch insertion on Aluminum Outserts
    6. Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
    7. Again, Spin test to ensure concentricity.
    8. Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
    9. Slide outsert over shaft and use the 3/32 Head retention Screw and Lock the Outsert in place!
    10. If using glue See steps 11-15 .
    11. We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
    12. Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
    13. Slide Outsert On shaft rotating to make sure Glue/Epoxy is evenly dispersed
    14. Use the 3/32 Head retention Screw and Lock the Outsert in place!
    15. Once The outsert is glued on Screw is installed stand the arrow on the nock end to dry.

Recently viewed

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
W
William Bagnara
Review

Thanks!