The Mathews LowPro Short Draw (SD) Detachable Quiver brings Mathews' streamlined, close-to-riser LowPro design to archers shooting shorter draw lengths and shorter arrows. Developed to solve fletching-clearance issues common with short-arrow setups, the LowPro SD features a shortened configuration that provides additional clearance around the lower arrow-retention arm while keeping arrows securely positioned on the bow.
Featuring a quick, quiet detachable mounting system and the integrated balance-focused design of the LowPro platform, this quiver is a practical accessory for shorter-draw bowhunters who want the functionality of a premium Mathews quiver without unwanted vane interference. It is especially relevant for properly fitted compact hunting bows, including short-draw configurations of the Mathews SOLACE.
Important: Check Your Arrow Length Before Ordering
Mathews recommends the LowPro SD Quiver when the distance from the tip of your arrow to the beginning of the vanes is less than 23 inches.
The Short Draw version accommodates arrows with a tip-to-vane measurement as short as 21 inches.
To determine whether you need the SD configuration:
- Take one of the completed arrows you intend to carry in the quiver.
- Measure from the tip of the arrow to the beginning of the vanes.
- If that measurement is less than 23 inches, select the LowPro SD rather than assuming the standard LowPro will provide enough clearance.
- Confirm that the measurement is at least 21 inches, which is Mathews' published minimum for the SD.
- Verify vane, broadhead, and mounting clearance after installing the quiver.
Measurement Note: This is not the same as carbon-to-carbon arrow shaft length, draw length, or a nock-to-point measurement. Mathews specifically uses the distance from the arrow tip to the beginning of the vanes to determine LowPro SD fitment.
Key Features
Purpose-Built for Shorter Draw Lengths and Arrows
The defining feature of the Mathews LowPro Short Draw Detachable Quiver is its shortened configuration.
Archers with shorter draw lengths commonly shoot shorter arrows. Depending on the quiver design, this can position the fletching close to the lower arrow-retention arm.
Without adequate clearance, the vanes may contact the quiver's retention components when arrows are installed or removed.
Mathews developed the LowPro SD specifically to address this issue while retaining the design advantages of its standard LowPro platform.
Rather than requiring shorter-draw shooters to accept compromised arrow positioning, the SD offers geometry better suited to their equipment.
Improved Fletching Clearance
The LowPro SD features a shorter arrangement designed to create more room around the arrow vanes and lower retention arm.
This helps prevent unwanted vane contact when using shorter hunting arrows.
For bowhunters shooting larger vane profiles, offset fletching, or helical configurations, proper clearance can be an important part of choosing a quiver.
The shortened design is intended to help address that clearance concern, but compatibility should still be checked using the actual finished arrows.
Setup Tip: Install all arrows and inspect their fletching with the quiver mounted on the bow. Make sure the vanes do not bind against the retention arm or other quiver components.
Fits Tip-to-Vane Measurements Down to 21 Inches
Mathews specifies that the LowPro SD accommodates arrows with a minimum measurement of 21 inches from the arrow tip to the beginning of the vanes.
For arrows measuring less than 23 inches using this method, Mathews identifies the SD as the required LowPro configuration.
This creates a useful fitment range for archers whose arrows are too short for proper clearance with the standard LowPro design.
For arrow configurations below the published 21-inch minimum, fitment should not be assumed.
Quick and Quiet Detachable Design
Like the standard LowPro Detachable Quiver, the SD incorporates a removable mounting arrangement designed for quick, quiet operation.
This gives hunters the flexibility to keep the quiver installed during the hunt or remove it after reaching their hunting position.
For example, some treestand or saddle hunters prefer shooting with the quiver removed, while others prefer maintaining the same bow balance throughout the hunt.
The detachable design allows the hunter to choose the setup that works best for their application.
Close-to-Riser Mounting
Mathews developed the LowPro platform to keep arrows positioned close to the riser.
Rather than extending the quiver farther away from the bow than necessary, the LowPro mounting system is designed to integrate closely with compatible Mathews hunting bow geometry.
This close-fitting arrangement can help reduce unnecessary accessory bulk and support Mathews' in-line balance philosophy.
For shorter-draw archers, the SD version retains this mounting approach while improving clearance for shorter arrows.
Designed for In-Line Balance
The positioning of a loaded quiver can affect how a bow balances in the shooter's hand.
Mathews designed the LowPro series to carry arrows close to the bow's riser, reducing how far the arrow load is positioned away from the bow.
This can be especially useful for hunters who prefer shooting with their quiver installed.
The final balance of the bow will depend on the sight, rest, stabilizers, arrow weight, and other installed accessories.
When setting up a hunting bow, we recommend evaluating balance with the quiver both installed and removed.
Engineered to Minimize Vibration
Mathews designed the LowPro system with a focus on secure arrow positioning, close integration, and reduced vibration.
A properly installed quiver should retain arrows without unnecessary movement during normal hunting use.
Secure arrow retention is especially important when walking through thick cover, climbing into a stand, or moving between hunting locations.
Always check the mounting mechanism and arrow retention before heading into the field.
Secure Arrow Retention
The SD retains the functionality of the standard LowPro platform while incorporating geometry better suited to shorter arrow configurations.
Its retention design is intended to keep arrows securely positioned without unwanted interference around the lower retention arm.
Shorter arrows should be checked individually to confirm proper placement, secure grip, and clearance around the fletching.
Arrow diameter and the specific fletching arrangement can influence how the complete setup fits.
A Practical Match for the Mathews SOLACE
The LowPro SD is particularly relevant for archers setting up the Mathews SOLACE, a premium hunting bow designed around shorter draw lengths and lighter draw weights.
Because shorter draw lengths frequently result in shorter finished arrows, the SD may provide the clearance needed for certain SOLACE arrow configurations.
However, not every SOLACE shooter automatically needs the SD.
The correct decision should be based on the measured tip-to-vane distance of the actual arrows being used.
This same principle applies to other compatible Mathews bows configured for shorter-draw archers.
Right-Hand and Left-Hand Configurations
The Mathews LowPro Short Draw Detachable Quiver is offered in right-handed and left-handed configurations.
Choose the version that matches your bow and intended mounting arrangement.
Handedness should be verified along with the hood finish before ordering.
Multiple Hood Finish Options
Mathews offers the LowPro SD with multiple hood-finish options, allowing shooters to coordinate the quiver with their bow.
Available finishes may include solid and camouflage options depending on current manufacturer inventory.
Select the exact finish and handedness combination offered for the product rather than assuming every color is available in every configuration.
Who It's Built For
The Mathews LowPro Short Draw Detachable Quiver is designed for bowhunters who use shorter arrows and need improved clearance around the lower quiver retention arm.
It is particularly well suited for archers who:
- Have shorter draw lengths and use correspondingly shorter hunting arrows.
- Measure less than 23 inches from the arrow tip to the beginning of the vanes.
- Need a LowPro configuration accommodating measurements as short as 21 inches.
- Experience fletching-clearance concerns with standard-length quivers.
- Want a detachable quiver that can be removed quickly and quietly.
- Prefer arrows positioned close to the bow riser.
- Want the balanced, streamlined design of the Mathews LowPro platform.
- Hunt whitetails from treestands, saddles, or ground blinds.
- Are setting up a Mathews SOLACE or another compatible shorter-draw hunting bow.
- Want to choose their quiver based on actual arrow dimensions rather than draw length alone.
For shooters with longer arrows that provide adequate clearance in the standard LowPro, the regular LowPro Detachable may be appropriate.
For hunters primarily interested in a slimmer hood profile for compatible two- and three-blade mechanical broadheads, the LowPro Slim Detachable addresses a different equipment requirement.
Specifications
Mathews LowPro Short Draw (SD) Detachable Quiver Specifications
| Specification |
Details |
| Brand |
Mathews Archery |
| Product |
LowPro Short Draw (SD) Detachable Quiver |
| Product Year |
2027 |
| Product Type |
Hunting Bow Quiver |
| Quiver Design |
Short Draw / Short Arrow |
| Mounting Style |
Low-Profile Detachable |
| Primary Feature |
Improved Fletching Clearance |
| Clearance Location |
Lower Arrow-Retention Arm |
| Standard LowPro Fitment Threshold |
SD Required Below 23" Tip to Vane |
| Minimum Supported Measurement |
21" Tip to Vane |
| Arrow Retention |
Secure LowPro Retention Design |
| Quiver Removal |
Quick and Quiet Detachment |
| Arrow Positioning |
Close to Bow Riser |
| Handedness |
Right Hand / Left Hand |
| Hood Finish |
Configuration Dependent |
| Bow Compatibility |
Compatible Mathews LowPro Platforms; Confirm Exact Model and Mounting Setup |
| Manufacturer Listed Price |
$259.99 |
Specifications are based on Mathews' published LowPro Short Draw Detachable Quiver information. The manufacturer states that arrows measuring less than 23 inches from tip to vane require the SD, with a minimum supported tip-to-vane distance of 21 inches. Confirm arrow dimensions, handedness, mounting compatibility, and finish before ordering.
LowPro Short Draw vs. Standard LowPro Detachable
The LowPro SD and standard LowPro Detachable are based on the same low-profile quiver concept, but they are designed for different arrow-length requirements.
| Feature |
LowPro Short Draw SD |
Standard LowPro Detachable |
| Primary Application |
Shorter Arrows |
Standard-Length Arrows |
| Detachable |
Yes |
Yes |
| Low-Profile Mounting |
Yes |
Yes |
| Close-to-Riser Design |
Yes |
Yes |
| Lower Retention Arm Clearance |
Optimized for Shorter Arrows |
Standard Configuration |
| Tip-to-Vane Below 23" |
Required by Mathews |
Not Recommended |
| Minimum Published Tip-to-Vane Fit |
21" |
Not Specified Here |
| Quick and Quiet Removal |
Yes |
Yes |
Which should you choose? Measure from your arrow tip to the beginning of the vanes. If the measurement is less than 23 inches but at least 21 inches, the LowPro SD is the manufacturer-specified configuration. With longer arrows, the standard LowPro may provide adequate clearance, subject to the rest of your bow setup.
LowPro Short Draw vs. LowPro Slim Detachable
Although the names sound similar, the Mathews LowPro Short Draw and LowPro Slim are designed to address different equipment requirements.
| Feature |
LowPro SD Detachable |
LowPro Slim Detachable |
| Primary Purpose |
Short-Arrow Vane Clearance |
Narrower Quiver Profile |
| Key Design Feature |
Shortened Quiver Geometry |
22% Slimmer Profile |
| Broadhead Focus |
Not Limited to a Slim-Specific Broadhead Category in Published Description |
2- and 3-Blade Mechanicals |
| Detachable Design |
Yes |
Yes |
| Close-to-Riser Mounting |
Yes |
Yes |
| Primary Fitment Check |
Arrow Tip-to-Vane Length |
Broadhead Hood Clearance |
Which should you choose? The SD is designed for archers whose shorter arrows require additional lower-retention-arm clearance. The Slim is designed for hunters who use compatible mechanical broadheads and want a narrower quiver profile.
The two designs are not interchangeable solutions. A slimmer hood does not automatically create the lower-retention-arm clearance provided by the Short Draw.
Our Take on the Mathews LowPro Short Draw Detachable Quiver
At Extreme Outfitters, we spend a lot of time helping archers match accessories to their actual bow and arrow configurations.
One thing that often gets overlooked when selecting a quiver is the length of the finished hunting arrows.
Someone with a shorter draw length may have a bow that fits perfectly, but their arrows can create clearance problems with a quiver designed around longer setups.
That's what makes the Mathews LowPro SD a useful addition to the lineup.
Rather than treating every archer as though they're shooting the same arrow length, Mathews designed a shortened LowPro specifically to improve clearance around the lower arrow-retention arm.
The published fitment guidance is particularly useful. If your arrow measures less than 23 inches from the tip to the start of the vanes, Mathews identifies the SD as the correct configuration, with a minimum supported measurement of 21 inches.
We think that measurement is the most important information to understand before purchasing.
We also like that Mathews retained the detachable LowPro design. Some bowhunters prefer leaving their quiver mounted, while others remove it once they reach their treestand or ground blind.
The close-to-riser mounting concept is another practical feature. Quiver position affects the balance of the complete bow, and keeping the arrow load close to the riser can help create a streamlined setup.
For archers setting up the Mathews SOLACE, the SD is particularly worth considering because the bow is designed around shorter draw lengths.
However, we wouldn't automatically recommend the SD to every SOLACE owner. The correct decision should be based on the dimensions of their actual finished arrows.
We would also be careful not to confuse the SD with the new LowPro Slim. The Slim is focused on reducing the quiver's profile for compatible mechanical broadheads, while the SD is focused on accommodating shorter arrows without vane interference.
For shorter-draw bowhunters who want a premium detachable Mathews quiver and need more clearance around their fletching, the LowPro Short Draw is a strong option.
Our recommendation is to measure the arrow correctly, verify the bow's mounting compatibility, and test arrow retention and vane clearance with the quiver installed before heading into the field.
Frequently Asked Questions
What is the Mathews LowPro Short Draw Detachable Quiver?
It is a shortened version of Mathews' LowPro Detachable Quiver designed for shorter-draw archers using shorter arrows. Its main benefit is improved fletching clearance around the lower arrow-retention arm.
What does SD stand for?
SD stands for Short Draw. The name identifies the quiver's shorter configuration designed around shorter arrow setups.
How do I know if I need the LowPro SD?
Measure from the tip of your completed arrow to the beginning of the vanes. Mathews states that arrows measuring less than 23 inches using this method require the SD.
What is the minimum arrow measurement for the SD Quiver?
Mathews lists a minimum tip-to-vane measurement of 21 inches for the LowPro SD.
Is the 21-inch measurement carbon-to-carbon arrow length?
No. Mathews measures from the arrow tip to the beginning of the vanes. This is different from carbon-to-carbon shaft length, draw length, or nock-to-point measurement.
Why does arrow length matter when choosing a quiver?
On shorter arrows, the fletching can sit too close to the lower arrow-retention arm of certain quivers. The SD's shortened geometry is designed to provide additional clearance and reduce unwanted vane contact.
Will the LowPro SD work with the Mathews SOLACE?
The SD is particularly relevant for SOLACE setups using shorter arrows. Confirm the exact mounting configuration and measure the finished arrow from tip to vane to determine whether the SD is required.
Do all short-draw archers need an SD Quiver?
No. The deciding factor is the finished arrow's tip-to-vane measurement, not draw length by itself. Some shorter-draw archers use arrows long enough for the standard LowPro.
Does the LowPro SD detach?
Yes. It retains the detachable LowPro design for quick, quiet removal.
Can I leave the LowPro SD mounted while shooting?
The quiver is designed to remain securely mounted during normal use. Whether to shoot with the quiver installed or removed comes down to personal preference and the balance of the complete setup.
Does the SD improve bow balance?
It incorporates Mathews' LowPro close-to-riser mounting philosophy, intended to support in-line balance and minimize vibration. Actual balance depends on the bow, arrows, and other installed accessories.
What's the difference between the LowPro SD and LowPro Slim?
The SD uses shortened geometry to accommodate shorter arrows and improve vane clearance. The Slim focuses on a narrower hood profile designed for compatible two- and three-blade mechanical broadheads.
Is the LowPro SD the same as the standard LowPro Detachable?
No. Although both use the LowPro detachable concept, the SD is specifically shortened to address the clearance needs of shorter arrow configurations.
Is the SD Quiver available for left-handed bows?
Yes. Mathews offers right-handed and left-handed configurations.
Does the LowPro SD come in different colors?
Mathews offers multiple hood-finish selections. Available combinations depend on current manufacturer and dealer inventory.
Will the LowPro SD fit every Mathews bow?
Compatibility should not be assumed across every Mathews model. Confirm that your exact bow supports the LowPro detachable mounting system and that your sight, rest, and other accessories allow proper installation.
Can I use fixed-blade broadheads with the LowPro SD?
The manufacturer describes the SD primarily in terms of short-arrow and vane clearance rather than the Slim series' specific mechanical-broadhead hood design. Always verify the dimensions and fit of your exact broadheads before use.
Will the SD work with large or high-profile vanes?
The shortened design provides improved clearance around the lower retention arm, but clearance is not guaranteed for every vane height or fletching configuration. Check the actual finished arrows after installing the quiver.
Does the LowPro SD include arrows or broadheads?
The LowPro SD is sold as a quiver accessory. Arrows and broadheads are not advertised as included.
Where can I buy the Mathews LowPro SD Quiver?
Explore Mathews accessories at Extreme Outfitters or contact our archery team in Jacksonville, North Carolina, for help with arrow measurements, compatibility, and availability.
Explore More Mathews Quivers and Accessories
The LowPro Short Draw Detachable Quiver offers a purpose-built solution for archers using shorter hunting arrows.
Browse our Mathews Archery collection for compatible accessories, or explore our hunting bow quivers to compare additional models.
You can also explore our bow accessories collection when building or upgrading your complete hunting setup.
Complete Your Short-Draw Hunting Setup
Choosing the right quiver is about more than matching a bow model. Arrow length, fletching placement, broadhead clearance, mounting compatibility, and the balance of the finished bow all need to be considered.
At Extreme Outfitters, our archery pro shop in Jacksonville, North Carolina, helps bowhunters choose compatible accessories and build equipment around their individual shooting requirements.
Ready to upgrade? Select your hood finish and handedness, confirm that your arrow tip-to-vane measurement falls within the supported range, and add the Mathews LowPro Short Draw Detachable Quiver to your cart.
Need help determining whether the SD or standard LowPro is the correct quiver? Contact our archery team at 910-355-2118 for assistance.
